Watery Filters is reader-supported. When you purchase via links on our site, we may earn an affiliate commission at no extra cost to you. Learn more.

Is Your Brita Filter Not Sealing Properly? Most Common Reasons

Brita-Filter-Not-SealingEver since you were a little kid, you would hear this cliché statement that water is the building block of life, it is an essential part of life, and that it makes up 70 percent of your body which speaks for its importance itself.

Because of the environmental effects on the water, it loses its purity and natural state, causing it to be contaminated even when it is disinfected by using chlorine and other water treatment procedures, it still loses its natural odourless form and taste.

This is why using a water filter is becoming increasingly popular, especially with the increasing impurities present in groundwater as well as tap water. A water filter efficiently gets rid of 90 percent of most contaminants found in water such as cadmium, lead, chlorine, etc.

Water filters are of different types and depend on the customer’s preferences as well as the level of water contamination and filter requirement. Brita water filter provides various options to choose from depending on what you want. Brita filters are a customer favourite because they last longer than most of their competitors and they are also kinder for the environment. But at some point, you might notice that your Brita water filter is not sealing correctly.

This article will find the most common reasons you are having problems with the seal of your Brita Filter and hopefully will find effective solutions so you can take advantage of your precious water filter.

Is Your Brita Filter Not Sealing Properly – Most Common Reasons

Following are some possible reasons your Brita filter might not be sealing properly;

The Filter Is Loose


If you are using a Brita faucet filter, you might notice that it is not sealed properly which is why it causes leakage in the faucet/ This means that the filter is loose and is not correctly screwed on the faucet. If you notice that your faucet is splattering water in a strange manner, this means that the filter is not sealed correctly.

When you install or screw the filter in place make sure that it is aligned properly with the faucet so that you don’t run the chances of the faucet loosely hanging around the tap. When you press down the filter, you may also hear a snapping sound that reassures that the filter has been firmly screwed on.

Installation Not Done Correctly

Another common reason is not installing the filters properly and this goes for all of the Brita water filters, if you take the installation process lightly, you will have consistent problems with the water filter not sealing properly. The key is to align the filter correctly with the reservoir in case of pitchers and dispensers while in the faucets, you should be able to hear a click sound that indicates correct installation.

Air Bubbles

This is the most common reason why your filter is not sealing properly and as a result, the water filter seems to be leaking because the air pockets cause tension around the filter. An easy solution is to wash and soak the water filter in cold water and let it stay there for half an hour. Another effective method is to gently tap on the water filter which will release the trapped air bubbles.

Are You Pouring It Wrong?

This problem can occur if you are too careless with the way you put the water inside either the dispenser or the water filter pitcher where the water poured in a pressured manner will cause the filter to malfunction, causing stress around it.

Also, make sure you do not pour hot water into the filter as it may cause the filter to become porous and it is not a good sign because the unfiltered water will seep through the filter without performing the filtration function properly and you will end up with contaminated water.

Make sure you use water at a cool or normal temperature to avoid any damage to the filter contents and improve its life, filtration and performance, a little care goes a long way.

Residues Causing Trouble

The water filter can get worn out over time and this will result in an increase in sediments around the housing area of the filter which will result in leaking and which means that the filter is not sealing properly.

If you are using the water filter in a faucet, you can easily remove it by using a strong cleaner or just use a mixture of water and vinegar to get rid of the extra dirt around the filter area. Make sure you remove it correctly so as not to damage the filter contents and also be careful placing it back onto the mounting collar of the faucet.

For filters inside the pitchers, you may need to spray water in force to the filter from the opposite direction in order for the sediments and grime to fall off from the filter but you have to be extra careful while doing so

FAQS

What kind of impurities are filtered by a Brita FIlter?

While it depends on which Brita water filter you are using, the most common contaminants removed by a Brita Filter are zinc, cadmium, lead, mercury, chlorine, etc.

Is the smell coming from water a normal case?

It depends on the type of smell that is coming from the water; if it smells like bleach or chlorine, that is just the disinfectant used to treat contaminated water which is completely normal. If it smells something like the ocean or rotten egg, that means your water needs to purify, you can always use a water filter with carbon to eliminate impurities and bad odour from water.

Final Thoughts

Water is best when it is consumed in its purest form and what better than a good filter like Brita to do the job efficiently. Even though there can be minor problems with the Brita filter, they can be easily solved if you are a little bit careful.